1 HP 750 Watt Computer Controller and Matching Servo Motor fits Many Mini Metal Lathes. Of all threading gears and auto feed systems. Fits mini metal lathes that the drive belt goes directly to the spindle gear. Does not fit mini metal lathes that have an intermediate shaft (high/low gear). To fit these you would need a different top gear and a different belt.
Individual parts, motor mount, timing belt with timing gears, spacers and adapters are available. See my other listings for a kit to instal your own motor. Kinda like replacing the small block with a big block in your Mustang/Camaro muscle car.
Just pure power, so much so that you will never use all of it. This system provides full power at any speed and that includes Spindle RPM's as low as 60 RPM's. Motor and spindle speeds + Reverse. The motor speed can be. And or full range can be achieved with just the speed control lever.Only requires a few easy steps. Reverse is simple, just hold the yellow button for a few seconds. Includes the ability to set bottom and top RPM range separately. In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below). Slowest speed achievable: Motor 100 RPM = Spindle 60 RPM. Highest speed this one produced: Motor 3,500 RPM = Spindle just over 2,000 RPM's. Note: it is not recommended to spin the spindle any faster unless you upgrade the factory installed spindle bearings.
On You Tube search for. Mini Metal Lathe 1 HP Servo Motor 750 Watt Computer controlled with threading and gears Same username the custom crafter.
This listing is for a fully alpha tested system like the one seen in the photos. This includes the modified control unit with thermal overload protection and the optional grade 8 set screw/pin. A new 750 watt motor like the one seen here in photos and on you-tube. Motor will come with the motor mount installed and locked in the proper location for the test lathe.This may require adjustment to fit your lathe. It will also come with the small timing pulley installed on it by a custom made shear pin. (You get one of the 2 aluminum set screws see in photos and one grade 8 hardened steel set screw). A new control computer like the one seen in photos and on you-tube. This control unit is modified by The Custom Crafter to include a thermal overload system with reset button.
A new speed control switch like the one seen in photos and on you-tube. The Custom Crafter made in the USA motor mount.
(installed on motor, see line 1). The Custom Crafter made in USA spindle bearing head adapter (see photos).
The Custom Crafter made in USA spindle spacer (see photos). The USA made in steel spindle timing pulley re-machined by The Custom Crafter to fit spindle (see photos). The USA made in steel motor timing pulley re-machined by the Custom Crafter to fit the motor (see photos). Comes preinstalled on motor (see line 1).A new timing belt not used in the quality control testing of this system. A small parts package with mounting nuts and thick washers. The Custom Crafter quick program and spindle speed card. Package will include written step by step assembly instructions or a video link will be provided. This will include a text number for direct assistance from the custom Crafter. Assembly requires some technical skill to include minor machine work. You will have to cut the die-cast gear housing to allow additional room for the larger timing belt. (see photos) this can be done with a hacksaw and a file but a pneumatic cut off tool or die grinder will ease this job. A spreader wrench is a big help but this can be managed with a hammer and punch. You will need metric and domestic allen wrenches + a 13mm/1/2 deep socket and ratchet.
Some longer allen head metric allen head bolts (not included) may also be required, especially it you over tighten and strip the factory bolts provided with your machine. This system has so much more power that it becomes tempting to see just how much you can cut in a single pass. Do not do this because the rest of the mini lathe is not built strong/stable enough for this kind of abuse. If you jam it, you may damage the lathe to include broken cutters, parts and the control unit.
All lathes are dangerous, increasing the. To insure fit and proper application. Is suitable for your intended use. Large flat rate box and to USA only. I will re address close.
Main components have a unique internal water soluble identification mark. No return authorizations will be issued after the 10 day period.See details, what's covered and for how long etc below. If found to be abuse or missing the. Or demos that I have from previous builds. Additionally original packaging such as styrofoam package inserts must be used to return these parts.
Timing pulleys, motor mount and aluminum adapters. Timing belt and small parts are not covered. The item "Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit Fits Original Location Gear" is in sale since Monday, April 6, 2020.
This item is in the category "Home & Garden\Tools & Workshop Equipment\Power Tools\Lathes". The seller is "thecustomcrafter" and is located in Haines City, Florida. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Turks and caicos islands, Bangladesh, Brunei darussalam, Bolivia, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Luxembourg, Monaco, Macao, Martinique, Nicaragua, Pakistan, Paraguay, Uruguay.