Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input

Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input
Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input

Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input

1 HP 750 Watt Servo Motor with Computer Driver/Controller and switched remote control capability. Fits Many Mini Metal Lathes.

Runs on normal household 115 Volt outlets. In the original motor location of your spindle drive mini metal lathe. Of all threading gears, auto feed systems and remote control via CNC or. Forward and an emergency stop. Each of the three speeds can be set as follows. Anywhere between 300 and 1,000 RPM. Anywhere between 900 and 3,200 RPM. Anywhere between 2,000 and 4,500 RPM. Emergency cut off/power stop function.

Each of which is energized by a single on off contact via wire. Connectors on the back of the control unit. Fits mini metal lathes that the drive belt goes directly to the spindle gear. Does not fit mini metal lathes that have an intermediate shaft (high/low gear). Individual parts, motor mount, timing belt with timing gears, spacers and adapters are available.

See my other listings for a kit to. Kinda like replacing the small block with a big block in your Mustang/Camaro muscle car. Just pure power, so much so that you will never use all of it. This system provides full power at any speed and that includes Spindle RPM's as low as 200 RPM's.

Motor and spindle speeds + Reverse. The motor speed can be. And or full range can be achieved with just the speed control lever. Only requires a few easy steps.

Reverse is simple, just hold the yellow button for a few seconds. Includes the ability to set bottom and top RPM range separately. In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below).

Slowest speed achievable: Motor 100 RPM = Spindle 60 RPM. Highest speed this one produced: Motor 3,500 RPM = Spindle just over 2,000 RPM's. Note: it is not recommended to spin the spindle any faster unless you upgrade the factory installed spindle bearings. See it (prototype 1) running. On You Tube search for.

Mini Metal Lathe 1 HP Servo Motor 750 Watt Computer controlled with threading and gears Same username The Custom Crafter. This listing is for a fully alpha tested system like the one seen in the photos. This includes the modified control unit with thermal overload protection, internal speed control and break out box on back for remote control. A new 750 watt motor like the one seen here in photos and on you-tube. Motor will come with the motor mount installed and locked in the proper location for the test lathe. This may require adjustment to fit your lathe. It will also come with the small timing pulley installed on it using a 4mm key-way and main shaft nut. A new control computer like the one seen in the above photos. This control unit is modified by The Custom Crafter to include: A. Thermal overload system with reset button. (see photo, make note, color of the reset button may be black or red). Three adjustable speeds forward which can activated remotely by a single pole single throw switch or relay. Just remove the red jumper wire and connect your switch. The Custom Crafter made in the USA motor mount. (installed on motor, see line 1). Includes thick washers and grade 8 nuts. The Custom Crafter made in USA spindle bearing head adapter (see photos).

The Custom Crafter made in USA spindle spacer (see photos). One aluminum spindle timing pulley re-machined by The Custom Crafter to fit spindle (see photos). One aluminum motor timing pulley re-machined by the Custom Crafter to fit the motor (see photos). Comes preinstalled on motor (see line 1). A new L050 1/2 wide timing belt.

The Custom Crafter quick program and spindle speed card. Package will include basic written assembly instructions. This will include a text number for direct assistance from the custom Crafter.

Assembly requires some technical skill to include minor machine work. Note: Check the photos in this listing.

If your lathe has holes instead of the normal slots, this motor will not fit without your ability to slot the cast iron lathe bed. You will have to cut the die-cast gear housing to allow additional room for the larger timing belt. (see photos) this can be done with a hacksaw and a file but a pneumatic cut off tool or die grinder will ease this job. A spreader wrench is a big help but this can be managed with a hammer and punch.

You will need metric and domestic allen wrenches + a 13mm/1/2 deep socket and ratchet. Some longer allen head metric allen head bolts (not included) may also be required, especially it you over tighten and strip the factory bolts provided with your machine.

This system has so much more power that it becomes tempting to see just how much you can cut in a single pass. Do not do this because the rest of the mini lathe is not built strong/stable enough for this kind of abuse. If you jam it, you may damage the lathe to include broken cutters, parts and the control unit.

All lathes are dangerous, increasing the. To insure fit and proper application. Is suitable for your intended use. I love it great product and support.

Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit Fits Original Location Gear. Large flat rate box and to USA only. Be added to the order. Main components have a unique internal water soluble identification mark.

No return authorizations will be issued after the 10 day period. See details, what's covered and for how long etc below.

If found to be abuse or missing the. Or demos that I have from previous builds. Additionally original packaging such as Styrofoam package inserts must be used to return these parts.

Timing pulleys, motor mount and aluminum adapters. Timing belt and small parts are not covered. Ask questions before ordering: Do not worry about missing this item. Also as I build them, they are improved as I never cut corners to save penny's.

The item "Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input" is in sale since Wednesday, December 30, 2020. This item is in the category "Home & Garden\Tools & Workshop Equipment\Power Tools\Lathes". The seller is "thecustomcrafter" and is located in Haines City, Florida.

This item can be shipped to United States.


Mini Metal Lathe 1 HP Servo Motor 115 V 750 Watt Kit With CNC switched input